nadie sabe que podria ser?
las mks tft no necesitan configuracion en marlin ¿no?
he probado con todos los baudios de comunicacion y nada.
#--------------------------------------------------------------------
######### Printer type setting ##################################
#mainboard firmware setting(marlin:1; repetier:2; smoothie:3)
>cfg_firmware_type:1
#machine setting (Normal:1; Delta:2)
>cfg_machine_type:1
#baud rate (9600:1; 57600:2; 115200:3; 250000:4)
>cfg_baud_rate:3
#multi-language(enable:1, disable:0)
>cfg_multiple_language:1
#languages setting(simplified (simplified Chinese:1; traditional Chinese:2; English:3; Russian:4; Spanish:5;French:6;Italian:7).
#This configuration is valid when "cfg_multiple_language" is disabled.
>cfg_language_type:5
#extruder number(one:1; dual:2)
>cfg_sprayer_counter:1
#enable heated bed(yes:1; no: 0)
>cfg_custom_bed_flag:1
#the max target temp of extruder and heated bed
>cfg_max_sprayer_temperature:270
>cfg_max_hotbed_temperature:150
#pause position (-1 is invalid; Z-axis is relative position)
>cfg_XPOS:-1
>cfg_YPOS:-1
>cfg_ZADD:10
#-----------------------------------------------------------------------
######### Advanced Function Option ##################################
#enable UPS?(yes:1; no:0)
>cfg_have_ups_device:0
#enable power detecting module(mks 220det:1; mks pwc:0)
>cfg_insert_det_module:0
#enable auto off after print finish function (no:0; Yes:1)
>cfg_print_finish_close_Machine:0
#set PB0 signal when use it for sencond nozzle (high level:1; low level:0)
>cfg_PB0_trigger_Level:0
#set PB1 signal (high level:1; low level:0)
>cfg_PB1_trigger_Level:0
#set error range of Z-axis on breakpoints recovery
>cfg_breakpoint_z_error:0.2
#the function of power detecting and filament detecting(1:disable;0:enable)
>cfg_mask_PB0_PB1_function:0
# the method of save the gcode data with power off(1:Capacitor storage; 0:File system save)
>cfg_pwroff_save_mode:0
#---------------------------------------------------------------------------
######### Filament Change Function ##############################
#the speed to extrude filament(mm/min)
>cfg_filament_load_speed:1200
#the lenght to extrude filament (mm)
>cfg_filament_load_length:200
#the speed to retract filament(mm/min)
>cfg_filament_unload_speed:1200
#the lenght to retract filament(mm)
>cfg_filament_unload_length:200
#It is the minimum temperature for filament change.
It will auto heat up if the current temp doesn't reach the target.
>cfg_filament_load_limit_temperature:200
#---------------------------------------------------------------------------
############ Leveling Function ########################################
#leveling mode(manual:0; auto:1; conceal leveling button:2)
>cfg_leveling_mode:0
#the command of auto leveling (G29 is available for Marlin.While G32 is for Repetier and Smoothieware)
>cfg_auto_leveling_cmd:G28;G29;
#the point number of manual leveling
3,4,5 point available)
>cfg_point_number:5
#the coordinates of 5 point on manual leveling
>cfg_point1:50,50
>cfg_point2:180,50
>cfg_point3:180,180
>cfg_point4:50,180
>cfg_point5:150,150
#the travel speed of leveling(mm/min)
>cfg_leveling_z_speed:1500
>cfg_leveling_xy_speed:3000
#When the XY axis is moved manually, the height of the z-axis of the extruded Z axis from the origin (mm)
#normally only needs to be reconfigured when the z axis is zero to the maximum under the smoothware firmware.
> cfg_leveling_z_high: 10
#---------------------------------------------------------------------------
############# WIFI Function ##########################################
#wifi mode(AP:1; STA:0)
>cfg_wifi_mode:1
#wifi name and password
>cfg_wifi_ap_name:MKS_wifi
>cfg_wifi_key_code:makerbase
#0:disable cloud service 1:enable cloud service
>cfg_cloud_enable:1
#cloud service adress
>cfg_wifi_cloud_host:www.baizhongyun.cn
#cloud service port
>cfg_cloud_port:10086
#Dynamic access IP
>cfg_ip_dhcp_flag:1
#--------------------------------------------------------------------------------
############## Function Customization #######################################
#functional button:
#in the style of simple, the functional button display in the "set" interface
#in the style of Classic,the functional button display in the "home" interface
#functional button(0:no display; 1:display)
>cfg_function_btn1_display:1
#the functional button 1 command
>function_btn1_cmd:M84;
#The "stop" button below the "Home" interface(0:disable,1:enable)
>cfg_quickstop_btn_display:0
#The "zoffset" button below the "More" interface(0:disable,1:enable)
>cfg_zprob_offset_btn_display:0
#set number of "More" button
>moreitem_pic_cnt:0
#edit command for 1~7 "More" button,each command must be separated by semicolon ";"
>moreitem_button1_cmd:G28 X0;
>moreitem_button2_cmd:G28 X0;
>moreitem_button3_cmd:G28 Y0;
>moreitem_button4_cmd:G28 Y0;
>moreitem_button5_cmd:G28 Z0;
>moreitem_button6_cmd:G28 Z0;
>moreitem_button7_cmd:G28;
#how many "More" button display on screen interface
>morefunc_cnt:0
#command setting on button1~7
>morefunc1_cmd:G28;
>morefunc2_cmd:G28;
>morefunc3_cmd:G28;
>morefunc4_cmd:G28;
>morefunc5_cmd:G28;
>morefunc6_cmd:G28;
>morefunc7_cmd:G28;
#---------------------------------------------------------------------------------
##### Display Customization(button and logo customized see User's Manual) #######
#the color of screen background
>cfg_background_color:0x000000
#the color of title text
>cfg_title_color:0xFFFFFF
#the color of temperature,fan,(etc) background
>cfg_state_bkcolor:0x000000
#the color of temprature,fan,(etc) text
>cfg_state_text_color:0xFFFFFF
#the color of file button
>cfg_filename_bkcolor:0x000000
#the color of file text
>cfg_filename_textcolor:0xFFFFFF
#the color of general button background
>cfg_btn_bkcolor:0x000000
#the color of general button text
>cfg_btn_textcolor:0xFFFFFF
#the color of status button background
>cfg_state_btn_bkcolor:0x000000
#the color of status button text
>cfg_state_btn_textcolor:0xFFFFFF
#the color of "back" button background
>cfg_back_btn_bkcolor:0x000000
#the color of "back" button text
>cfg_back_btn_textcolor:0xFFFFFF
#the color of selected button background
>cfg_sel_btn_bkcolor:0x000000
#the color of selected button text
>cfg_sel_btn_textcolor:0xFFFFFF
#the color of dialog button background
>cfg_dialog_btn_bkcolor:0xff0000
#the color of dialog button text
>cfg_dialog_btn_textcolor:0xFFFFFF
#3D effects setting (disable: 0; enable: 1)
>cfg_BUTTON_3D_effects:0
#position of button font offset bottom(unit:pixel)
>cfg_btn_text_offset:23
##Screen rotation 180 °(0:disable,0xEE:enable)
>cfg_screen_overturn_180:0x00
#the style of display on the screen home(0:classic,1
imple)
>cfg_screen_display_mode:1
#Enable function of display error message. (no:0; Yes:1)
>cfg_display_eeror_message:0
#-----------------------------------------------------------------------