30-09-2020, 06:53 PM
Hola estoy intentando actualizar la placa de mi anet con marlín 1.1.9.1 a Marlín 2.0 con Visual Studio Code y me da fallo al subirlo. El vídeo que he seguido es ese:
[video=youtube] https://www.youtube.com/watch?v=RhfnzML02bw&t=1s[/video]
[video=youtube] https://www.youtube.com/watch?v=RhfnzML02bw&t=1s[/video]
Código:
Windows PowerShell
Copyright (C) Microsoft Corporation. Todos los derechos reservados.
Prueba la nueva tecnología PowerShell multiplataforma https://aka.ms/pscore6
PS C:\Users\samue\OneDrive\Escritorio\Instalar Marlin\Marlin-2.0.x> platformio run --target upload -e sanguino1284p
Processing sanguino1284p (platform: atmelavr; board: sanguino_atmega1284p; framework: arduino)
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Verbose mode can be enabled via `-v, --verbose` option
CONFIGURATION: https://docs.platformio.org/page/boards/atmelavr/sanguino_atmega1284p.html
PLATFORM: Atmel AVR (2.2.0) > Sanguino ATmega1284p (16MHz)
HARDWARE: ATMEGA1284P 16MHz, 16KB RAM, 124KB Flash
DEBUG: Current (simavr) On-board (simavr)
PACKAGES:
- framework-arduino-avr 5.0.0
- tool-avrdude 1.60300.200527 (6.3.0)
- toolchain-atmelavr 1.50400.190710 (5.4.0)
Converting Marlin.ino
LDF: Library Dependency Finder -> http://bit.ly/configure-pio-ldf
LDF Modes: Finder ~ chain, Compatibility ~ soft
Found 6 compatible libraries
Scanning dependencies...
Dependency Graph
|-- <LiquidCrystal> 1.5.0
| |-- <Wire> 1.0
|-- <Wire> 1.0
|-- <SPI> 1.0
|-- <EEPROM> 2.0
|-- <SoftwareSerial> 1.0
Building in release mode
Checking size .pio\build\sanguino1284p\firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [== ] 25.0% (used 4096 bytes from 16384 bytes)
Flash: [========= ] 88.1% (used 111894 bytes from 126976 bytes)
Configuring upload protocol...
AVAILABLE: arduino
CURRENT: upload_protocol = arduino
Looking for upload port...
Auto-detected: COM4
Uploading .pio\build\sanguino1284p\firmware.hex
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x73
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x74
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x61
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x72
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x74
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x0a
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x65
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x63
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x68
avrdude done. Thank you.
*** [upload] Error 1
================================================================================================== [FAILED] Took 58.08 seconds ==================================================================================================
Environment Status Duration
------------- -------- ------------
sanguino1284p FAILED 00:00:58.078
============================================================================================= 1 failed, 0 succeeded in 00:00:58.078 =============================================================================================PS C:\Users\samue\OneDrive\Escritorio\Instalar Marlin\Marlin-2.0.x> echo "done" >C:\Users\samue\AppData\Local\Temp\ipc
PS C:\Users\samue\OneDrive\Escritorio\Instalar Marlin\Marlin-2.0.x>