This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

  • 1 voto(s) - 5 Media
  • 1
  • 2
  • 3
  • 4
  • 5
Problemas al subir Marlin OVM20 Anet
#1
Buenas gente. Por fin me llegó la placa OVM20 Anet que mi mujer reservo antes de Navidad, y al poner a imprimir, pues los pasos por mm están asi asi, la eeprom esta capada, el firm en inglés y algún desastre más que quiero cambiar. La cuestión es que me pongo a meterle el marlín 2.0 que yo tenia antes configurado para la anet en la placa original, y el arduino me manda error al subir el firm. Si conecto a pronterface lo hace perfecto, se mueve, conecta y todo bien, pero con arduino nada. El programador tengo puesto el AVRISP MKII, placa anet v1.0 y puerto el COM que me salta cuando la conecto al PC.
Utilizo arduino 1.8.7, y he probado con el 1.9 beta y me pasa lo mismo
El mensaje que me da arduino es este:
 
 
 
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 1 of 10: not in sync: resp=0x74
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 2 of 10: not in sync: resp=0x74
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 3 of 10: not in sync: resp=0x74
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 4 of 10: not in sync: resp=0x74
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 5 of 10: not in sync: resp=0x74
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 6 of 10: not in sync: resp=0x74
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 7 of 10: not in sync: resp=0x74
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 8 of 10: not in sync: resp=0x74
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 9 of 10: not in sync: resp=0x74
avrdude: stk500_recv(): programmer is not responding
avrdude: stk500_getsync() attempt 10 of 10: not in sync: resp=0x74
  Responder
#2
Hola, según indican en la web de Staticboards, hay que configurar la placa como Anet V1.0 (Optiboot).
El bootloader Optiboot funciona a 115200 baudios y el normal a 57600 baudios.
  Responder
#3
Muchas gracias Simemart.
Pues probé el Optiboot, que no habia visto en su web, y me daba el mismo error. Así que desinstale arduino por completo y lo volví a instalar y ya funcionó con el Optiboot. Gracias!
PD: con el 1.9 beta no he vuelto a probar, ya que solo lo utilicé como prueba a ver
  Responder


Posibles temas similares…
Tema Autor Respuestas Vistas Último mensaje
  De Marlin 2.0.9 a Marlin 2.12 21Curiosos 3 268 22-01-2023, 09:36 PM
Último mensaje: 21Curiosos
  OVM20 Lite_Marlin2.1_BLtouch y Sensor de Filamento xavibox66 0 246 19-08-2022, 11:40 AM
Último mensaje: xavibox66
  Problemas configuraion MARLIN BLTOUCH 21Curiosos 2 397 21-05-2022, 02:28 PM
Último mensaje: 21Curiosos
  Ender-3 v2 subir temperatura Hotend Faoapa 4 983 24-01-2022, 08:28 AM
Último mensaje: Faoapa
  CONSULTA Marlin 2.0.7.2, Anet A8 y Power Loss Recovery jjvelar 5 1,770 07-11-2020, 01:17 PM
Último mensaje: jjvelar