This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

  • 0 voto(s) - 0 Media
  • 1
  • 2
  • 3
  • 4
  • 5
Cosa extraña al finalizar piezas
#1
Buenas, venia a comentar algo raro que me pasa en todas las piezas que hago últimamente.

[Imagen: yzu3eha8.jpg]

La ultima esquinita antes de terminar la deja sin hacer, si pongo varias piezas en la bandeja solo pasa en la ultima que hace....

¿Alguno sabe a que se puede deber?
  Responder
#2
A mi me pasaba hace unos meses, pero no recuerdo que hice que dejó de hacerlo. Me suena que actualicé a la última version de Repetier y Slic3r y se solucionó. Es una tontería pero es bastante molesto si buscas el mejor acabado posible. Tal vez alguien pueda ilustrarte mejor.
  Responder
#3
has puesto g-codes para que se ejecuten al acabar?
  Responder
#4
sacamantecas escribió:has puesto g-codes para que se ejecuten al acabar?

Nop
  Responder
#5
entonces habría que ver cuáles son los últimos g-codes que llegan a la impresora, porque ahí estará el misterio
  Responder
#6
Revisa un parametro de cache en la configuración de la impresora del repetier. A partir de la V1 de Arduino cambio ese valor y el repetier por defecto usa el valor antiguo.

Si no encuentras lo que es te lo busco. A ver si por ahí lo solucionas

saludos
  Responder
#7
Por cierto, prueba a imprimir una con otro soft (Cura) a ver si te lo hace

saludos
  Responder
#8
Mira, Aqui es donde te digo que debes tocar:

https://github.com/repetier/Repetier-Host/wiki/Setup

[Imagen: printersettings1.png]

Cita:With "Receive cache size" you define the size of the input buffer your firmware has. The input buffer of an arduino is 127 bytes, so 120 is a good value for most machines. The following checkbox sets, if we make use of it. Two versions are supported. In Ping-Pong mode, one command is send. After we receive an ok, which tells the command is stored or executed, the next command is send. It is easy, it is quite save, but is also quite slow. The conversion from USB->Serial->RepRap->Serial->USB has some latencies, which limit the throughput to 60-70 commands per second. This is for most applications fast enough. If you have a good connection, with no errors or use the repetier-protocol you will like the other option. If Ping-Pong is disabled, Repetier-Host will count the chars send without receiving an ok. In other terms, if the next command fits into the input buffer, it will send the next command. With the Repetier-Protocol there will be at least 4 commands in the buffer, more if they use only 1-2 parameter. On my computer, this boosts the speed to 240-250 commands per second.

Prueba a bajar el cache de recepción a 63. Puedes probar también el modo de comunicación a pingpong, a ver si así completa los finales.

Suerte

Saludos
  Responder
#9
Gracias! Una cosa nueva que aprendo.

Respecto al problema despues de trastear con ancho de extrusion y altura de capas no se porque pero ya no lo hace. Si me vuelve a ocurrir probare lo que me habeis comentado Sonrisa
  Responder


Posibles temas similares…
Tema Autor Respuestas Vistas Último mensaje
  Warping al finalizar impresión Albert90 12 4,174 09-01-2018, 06:09 PM
Último mensaje: fbforos