This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

  • 1 voto(s) - 4 Media
  • 1
  • 2
  • 3
  • 4
  • 5
Duda sobre si Ramps 1.4 es la número 33 ó 43
#1
Hola a todos, creo que es mi primera intervención después de mi presentación hace ya mucho tiempo, todas mis dudas las he ido resolviendo con el buscador, pero ahora tengo una que quizá no tenga mayor importancia pero que quiero resolver.

Ahora mismo, después de haber quemado un fusible de la GT2560 y mientras viene he colocado una Ramps 1.4. Pero a la hora de configurar Marlin me encontré con la duda de si debo colocar que es el número 33 ó 43, ya que he visto en algunos vídeos que hay quien coloca el 33, pero en las descripciones ese número se corresponde con la Ramps 1.3.
Gracias.
  Responder
#2
#define BOARD_RAMPS_13_EFB 33 // RAMPS 1.3 (Power outputs: Hotend, Fan, Bed)
#define BOARD_RAMPS_13_EEB 34 // RAMPS 1.3 (Power outputs: Hotend0, Hotend1, Bed)
#define BOARD_RAMPS_13_EFF 35 // RAMPS 1.3 (Power outputs: Hotend, Fan0, Fan1)
#define BOARD_RAMPS_13_EEF 36 // RAMPS 1.3 (Power outputs: Hotend0, Hotend1, Fan)
#define BOARD_RAMPS_13_SF 38 // RAMPS 1.3 (Power outputs: Spindle, Controller Fan)

#define BOARD_RAMPS_14_EFB 43 // RAMPS 1.4 (Power outputs: Hotend, Fan, Bed)
#define BOARD_RAMPS_14_EEB 44 // RAMPS 1.4 (Power outputs: Hotend0, Hotend1, Bed)
#define BOARD_RAMPS_14_EFF 45 // RAMPS 1.4 (Power outputs: Hotend, Fan0, Fan1)
#define BOARD_RAMPS_14_EEF 46 // RAMPS 1.4 (Power outputs: Hotend0, Hotend1, Fan)
#define BOARD_RAMPS_14_SF 48 // RAMPS 1.4 (Power outputs: Spindle, Controller Fan

hola , mira cual es tu caso, lo normal seria
#define BOARD_RAMPS_14_EFB 43 // RAMPS 1.4 (Power outputs: Hotend, Fan, Bed)

saludos
  Responder
#3
O sea, la 43. Entonces lo tengo bien. Gracias
  Responder


Posibles temas similares…
Tema Autor Respuestas Vistas Último mensaje
  DUDA Duda sobre unir modelos en 3d con meshmixer lc87 1 269 10-08-2022, 12:15 AM
Último mensaje: erjavi_zgz
  ¿ Cómo controlar el número de retracciones ? RocaDiesel 2 545 21-11-2021, 09:48 PM
Último mensaje: RocaDiesel
Sorprendido CONSULTA Skynet 2.3.2 + Anet A6....duda sobre errores de flasheo br0nka 3 2,706 11-02-2018, 01:44 AM
Último mensaje: br0nka
  error numero de linea +1 Coricoco 4 2,593 14-08-2014, 12:06 PM
Último mensaje: LoKus77