CONSULTA error al compilar exit status1 error al compilar tarjeta arduino uno

[nestordaniel]

no he podido compilarlo , desde ya muchas gracias por su tiempo

#include <LiquidCrystal.h>  // includes the LiquidCrystal Library
#include <math.h>    //para el redondeo
   
LiquidCrystal lcd(2, 3, 4, 5, 6, 7);  // Creates an LCD object. Parameters: (rs, enable, d4, d5, d6, d7)
// Connect panel using the standard lines.

// Sensor 1, trigger pin 13 y echo pin 12.
const int trigPin1 = 13;
const int echoPin1 = 12;

// Sensor 2, trigger pin 11 y echo pin 10.
const int trigPin2 = 11;
const int echoPin2 = 10;

// dimensiones Tanque 1 (el que esta en la parte inferior) en metros.
const float lengthBottomTankM = 3.2;
const float widthBottomTankM = 2;
const float deepBottomTankM = 1.7;
const float volTotalBottomTankM3 = 8.96;    // Restado 0.3 de distancia al sensor tanque inferior

// dimensiones Tanque 2 (el que esta en la parte inferior) en mestros
const float lengthUpTankM = 2.74;
const float widthUpTankM = 2;
const float deepUpTankM = 1.9;
const float volTotalUpTankM3 = 9.32;    // Restado 0.2 de distancia al sensor tanque superior
 
long duration1;
float deepBottomTankCm;

long duration2;
float deepUpTankCm;

float volumeBottomTank;
float volumeUpTank;

float porcBottomTank;
float porcUpTank;

void setup() {
  lcd.begin(16,2);  // Initializes the interface to the LCD screen, and specifies the dimensions (width and height) of the display
  pinMode(trigPin1, OUTPUT);
  pinMode(echoPin1, INPUT);
  pinMode(trigPin2, OUTPUT);
  pinMode(echoPin2, INPUT);
  Serial.begin (9600);   
}
 
void loop() {
// Trigger Lower tank
  digitalWrite(trigPin1, LOW);
  delayMicroseconds(2);
  digitalWrite(trigPin1, HIGH);
  delayMicroseconds(10);
  digitalWrite(trigPin1, LOW);
  duration1 = pulseIn(echoPin1, HIGH);
  deepBottomTankCm= duration1*0.034/2;

// Trigger upper tank
  digitalWrite(trigPin2, LOW);
  delayMicroseconds(2);
  digitalWrite(trigPin2, HIGH);
  delayMicroseconds(10);
  digitalWrite(trigPin2, LOW);
  duration2 = pulseIn(echoPin2, HIGH);
  deepUpTankCm= duration2*0.034/2;

if (deepBottomTankCm > 0 && deepUpTankCm > 0) {
// Make calculations based on volume1 and volume2
  volumeBottomTank = lengthBottomTankM * widthBottomTankM * (deepBottomTankM - (float)deepBottomTankCm/100);
     
  porcBottomTank = (float)volumeBottomTank/(float)volTotalBottomTankM3 * 100; 
 
  volumeBottomTank = round(volumeBottomTank*10);
  volumeBottomTank = volumeBottomTank/10;

  volumeUpTank = lengthUpTankM * widthUpTankM * (deepUpTankM - (float)deepUpTankCm/100);
  volumeUpTank = round(volumeUpTank*10);
  volumeUpTank = volumeUpTank/10;
  porcUpTank = (float)volumeUpTank / volTotalUpTankM3 * 100;

  Serial.println("cmBottom," + String(deepBottomTankCm) + ";
  cmUp," + String(deepUpTankCm));



// Show information on LCD
  lcd.setCursor(0,0);  // Sets the location at which subsequent text written to the LCD will be displayed
  lcd.println("S: " + String(volumeUpTank) + "m3, "+ String(round(porcUpTank)) + "%      ");  // Prints string "Distance" on the LCD
  lcd.println("DistaCm: " + String(deepUpTankCm) + "      ");
     
  delay(10);

  lcd.setCursor(0,1);
  lcd.println("I: " + String(volumeBottomTank) + "m3, "+ String(round(porcBottomTank)) + "%      ");
  lcd.println("DistCm: " + String(deepBottomTankCm) + "          ");
 
}
  delay(500);
}

[PauFerlo]

Si además del código incluyes el error que te tira el IDE será más probable que alguien se lo mire.
Saludos

[asesorplaza1]

Buenos días

El problema lo tienes en tus líneas 81 y 82

Código:

Serial.println("cmBottom," + String(deepBottomTankCm) + ";

  cmUp," + String(deepUpTankCm));

Esas líneas las has copiado mal, y la primera línea le has puesto los dos puntos para cerrarla, pero la orden esta a medias, la orden correcta es

Código:

    Serial.println("cmBottom," + String(deepBottomTankCm) + "cmUp," + String(deepUpTankCm));

Y así si compila

Un saludo.