14-06-2022, 07:00 PM
Hola de nuevo, tengo instalada la UPS de 24v de Bigthreetech y no se si lo tengo todo bien configurado
Mis dudas son sobre los apartados POWER_LOSS_PULLUP o PULLDOWN , no se cual he de activar (si es que tengo que activar alguno)
Ahora cuando apago la impresora, mantiene la corriente un tiempo , luego cuando se esta agotando la corriente de la UPS , apaga la pantalla y se queda pitando hasta que se descargan totalmente los condensadores.
¿Esto es el funcionamiento normal ? ¿El pitido se puede eliminar?
Saludos y gracias por adelantado
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
#define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
#define POWER_LOSS_ZRAISE 3 // (mm) Z axis raise on resume (on power loss with UPS)
#define POWER_LOSS_PIN PC0 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor
//#define POWER_LOSS_PULLDOWN
#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
// Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
// especially with "vase mode" printing. Set too high and vases cannot be continued.
#define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
// Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
//#define POWER_LOSS_RECOVER_ZHOME
#if ENABLED(POWER_LOSS_RECOVER_ZHOME)
//#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
#endif
#endif
Mis dudas son sobre los apartados POWER_LOSS_PULLUP o PULLDOWN , no se cual he de activar (si es que tengo que activar alguno)
Ahora cuando apago la impresora, mantiene la corriente un tiempo , luego cuando se esta agotando la corriente de la UPS , apaga la pantalla y se queda pitando hasta que se descargan totalmente los condensadores.
¿Esto es el funcionamiento normal ? ¿El pitido se puede eliminar?
Saludos y gracias por adelantado
#define POWER_LOSS_RECOVERY
#if ENABLED(POWER_LOSS_RECOVERY)
#define PLR_ENABLED_DEFAULT false // Power Loss Recovery enabled by default. (Set with 'M413 Sn' & M500)
#define BACKUP_POWER_SUPPLY // Backup power / UPS to move the steppers on power loss
#define POWER_LOSS_ZRAISE 3 // (mm) Z axis raise on resume (on power loss with UPS)
#define POWER_LOSS_PIN PC0 // Pin to detect power loss. Set to -1 to disable default pin on boards without module.
#define POWER_LOSS_STATE HIGH // State of pin indicating power loss
//#define POWER_LOSS_PULLUP // Set pullup / pulldown as appropriate for your sensor
//#define POWER_LOSS_PULLDOWN
#define POWER_LOSS_PURGE_LEN 20 // (mm) Length of filament to purge on resume
#define POWER_LOSS_RETRACT_LEN 10 // (mm) Length of filament to retract on fail. Requires backup power.
// Without a POWER_LOSS_PIN the following option helps reduce wear on the SD card,
// especially with "vase mode" printing. Set too high and vases cannot be continued.
#define POWER_LOSS_MIN_Z_CHANGE 0.05 // (mm) Minimum Z change before saving power-loss data
// Enable if Z homing is needed for proper recovery. 99.9% of the time this should be disabled!
//#define POWER_LOSS_RECOVER_ZHOME
#if ENABLED(POWER_LOSS_RECOVER_ZHOME)
//#define POWER_LOSS_ZHOME_POS { 0, 0 } // Safe XY position to home Z while avoiding objects on the bed
#endif
#endif