This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

  • 0 voto(s) - 0 Media
  • 1
  • 2
  • 3
  • 4
  • 5
Problema Autoleveling Sensor Inductivo
#1
Hola que tal! 
Feliz año y todo eso...
El caso es que he estado de vacaciones y me he puesto a trastear con la máquina de nuevo. La deje pendiente de instalar el autoleveling con un sensor inductivo que compré hace tiempo. Tengo uno capacitivo (de los naranjitos) y cuando pueda pues lo cambiare, pero de momento lo dejo así.

https://drive.google.com/open?id=0B-DE9m...GV6b2FLbnM

Como ya sabeis solamente detecta superficies metálicas. Mi cama es una plancha de aluminio de 3mm y encima un cristal de creo otros 3 ´o 4. No llega al fondo de la plancha, por lo que he tenido que recurrir a un apaño. He puesto papel de aluminio en las zonas que va a hacer el homing de z. 
El marlin lo tengo configurado de la siguiente manera:

//===========================================================================
//============================= Bed Auto Leveling ===========================
//===========================================================================

#define ENABLE_AUTO_BED_LEVELING // Delete the comment to enable (remove // at the start of the line)
//#define Z_PROBE_REPEATABILITY_TEST  // If not commented out, Z-Probe Repeatability test will be included if Auto Bed Leveling is Enabled.

#ifdef ENABLE_AUTO_BED_LEVELING

// There are 2 different ways to pick the X and Y locations to probe:

//  - "grid" mode
//    Probe every point in a rectangular grid
//    You must specify the rectangle, and the density of sample points
//    This mode is preferred because there are more measurements.
//    It used to be called ACCURATE_BED_LEVELING but "grid" is more descriptive

//  - "3-point" mode
//    Probe 3 arbitrary points on the bed (that aren't colinear)
//    You must specify the X & Y coordinates of all 3 points

#define AUTO_BED_LEVELING_GRID
// with AUTO_BED_LEVELING_GRID, the bed is sampled in a
// AUTO_BED_LEVELING_GRID_POINTSxAUTO_BED_LEVELING_GRID_POINTS grid
// and least squares solution is calculated
// Note: this feature occupies 10'206 byte
#ifdef AUTO_BED_LEVELING_GRID

// set the rectangle in which to probe
#define LEFT_PROBE_BED_POSITION 20
#define RIGHT_PROBE_BED_POSITION 195
#define BACK_PROBE_BED_POSITION 215
#define FRONT_PROBE_BED_POSITION 20

// set the number of grid points per dimension
// I wouldn't see a reason to go above 3 (=9 probing points on the bed)
#define AUTO_BED_LEVELING_GRID_POINTS 2


#else  // not AUTO_BED_LEVELING_GRID
// with no grid, just probe 3 arbitrary points.  A simple cross-product
// is used to esimate the plane of the print bed

#define ABL_PROBE_PT_1_X 15
#define ABL_PROBE_PT_1_Y 135
#define ABL_PROBE_PT_2_X 15
#define ABL_PROBE_PT_2_Y 20
#define ABL_PROBE_PT_3_X 170
#define ABL_PROBE_PT_3_Y 20

#endif // AUTO_BED_LEVELING_GRID


// these are the offsets to the probe relative to the extruder tip (Hotend - Probe)
// X and Y offsets must be integers
#define X_PROBE_OFFSET_FROM_EXTRUDER 0
#define Y_PROBE_OFFSET_FROM_EXTRUDER 0
#define Z_PROBE_OFFSET_FROM_EXTRUDER -1.35

#define Z_RAISE_BEFORE_HOMING 12       // (in mm) Raise Z before homing (G28) for Probe Clearance.
// Be sure you have this distance over your Z_MAX_POS in case

#define XY_TRAVEL_SPEED 6000         // X and Y axis travel speed between probes, in mm/min

#define Z_RAISE_BEFORE_PROBING 12   //How much the extruder will be raised before traveling to the first probing point.
#define Z_RAISE_BETWEEN_PROBINGS 3  //How much the extruder will be raised when traveling from between next probing points

//#define Z_PROBE_SLED // turn on if you have a z-probe mounted on a sled like those designed by Charles Bell
//#define SLED_DOCKING_OFFSET 5 // the extra distance the X axis must travel to pickup the sled. 0 should be fine but you can push it further if you'd like.

//If defined, the Probe servo will be turned on only during movement and then turned off to avoid jerk
//The value is the delay to turn the servo off after powered on - depends on the servo speed; 300ms is good value, but you can try lower it.
// You MUST HAVE the SERVO_ENDSTOPS defined to use here a value higher than zero otherwise your code will not compile.

#define PROBE_SERVO_DEACTIVATION_DELAY 300


//If you have enabled the Bed Auto Leveling and are using the same Z Probe for Z Homing,
//it is highly recommended you let this Z_SAFE_HOMING enabled!!!

#define Z_SAFE_HOMING   // This feature is meant to avoid Z homing with probe outside the bed area.
// When defined, it will:
// - Allow Z homing only after X and Y homing AND stepper drivers still enabled
// - If stepper drivers timeout, it will need X and Y homing again before Z homing
// - Position the probe in a defined XY point before Z Homing when homing all axis (G28)
// - Block Z homing only when the probe is outside bed area.

#ifdef Z_SAFE_HOMING

#define Z_SAFE_HOMING_X_POINT (X_MAX_LENGTH/2)    // X point for Z homing when homing all axis (G28)
#define Z_SAFE_HOMING_Y_POINT (Y_MAX_LENGTH/2)    // Y point for Z homing when homing all axis (G28)

#endif

#ifdef AUTO_BED_LEVELING_GRID // Check if Probe_Offset * Grid Points is greater than Probing Range
#if X_PROBE_OFFSET_FROM_EXTRUDER < 0
#if (-(X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
#endif
#else
#if ((X_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (RIGHT_PROBE_BED_POSITION - LEFT_PROBE_BED_POSITION))
#error "The X axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
#endif
#endif
#if Y_PROBE_OFFSET_FROM_EXTRUDER < 0
#if (-(Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
#endif
#else
#if ((Y_PROBE_OFFSET_FROM_EXTRUDER * (AUTO_BED_LEVELING_GRID_POINTS-1)) >= (BACK_PROBE_BED_POSITION - FRONT_PROBE_BED_POSITION))
#error "The Y axis probing range is not enough to fit all the points defined in AUTO_BED_LEVELING_GRID_POINTS"
#endif
#endif


#endif

#endif // ENABLE_AUTO_BED_LEVELING



y en el Repetir, en el Start Gcode tengo configurado esto, para que me haga el homing de z en uno de los 4 puntos que he configurado para el G29, porque si no se me iba al centro

G28 X Y ;
G1 X195 Y20 F8000;
G28 Z;
G1 Z2;
G28;
G29;
G1 Z2;

He hecho varias pruebas y cambiando el valor de zprobe he conseguido que se pegue el plástico en la cama , pero solo en una zona, en otras queda levantado y en otras muy hundido, es decir, el autoleveling no funciona bien aunque realmente los motores se mueven. 

He cambiado valores y siempre me saca el mismo plano normal, no entiendo si tengo algo mal configurado, entiendo que s´i. Alguien sabría ayudarme?
  Responder


Posibles temas similares…
Tema Autor Respuestas Vistas Último mensaje
  TO sensor abnormal josep882 0 898 13-10-2022, 06:08 PM
Último mensaje: josep882
  APORTE Sensor de final de filamento. Simemart 7 8,149 16-02-2021, 10:05 PM
Último mensaje: Simemart
  Reparar sensor de temperatura Insonorizate 8 5,052 16-09-2020, 04:25 PM
Último mensaje: joselrs42
  DUDA ¿Alguien tiene experiencia con este sensor? Edgard 0 667 05-07-2020, 01:42 PM
Último mensaje: Edgard
  CONSULTA sensor temperatura javi2 0 646 10-05-2020, 07:25 AM
Último mensaje: javi2